Diamond Abrasive Cutting Wire Saw

1. High efficiency and long lifespan
2. Competitive price and stable quality
3. Production capacity: 60,000 meters/month
4. Various wire saw types and sizes available
5. Good cutting result: smooth cutting, flat surface and even size

Diamond Abrasive Cutting Wire Saw

Experienced manufacturer of Diamond Abrasive Cutting Wire Saw, we supply diamond segments, diamond saw blades, diamond wire saw and diamond grinding tools for stone factories, quarries and wholesalers all over the world.


1. Diamond Wire Saw For Quarry:
Rubber wire is recommended, it can protect the wire saw rope very well and increase the wire’s strength. Rubber possesses excellent characteristic of temperature resistance, and it can be used under situation of water deficient. Strong flexibility can also reduce the cut-in-one-side problem.
2. Diamond Wire Saw For Block Trimming:
Plastic wire is recommended, it can be used to trim marble, granite and other stones. It could cut the blocks accurately with small inter-space.
3. Diamond Wire Saw For Profiling :
Plastic wire is recommended for shaping operations, it could provides a huge range of possibilities. It makes smooth surface and accurate sizes with small inter-space. Stone columns and special shape stone material for building industry can be processed in a much more economic way.
4. Diamond Wire Saw For Reinforce Concrete Cutting:
Diameter 10.5/11.5mm Rubber and Spring wire is recommended. The wires are widely used in the reinforced concrete with more than 5% steel inside. It is used in the building constructions, cutting for houses, bridges, cement pipes and under water buildings.
5. Diamond Multi-Wire Saw For Slab Cutting:
Diamond multi-cutting wire saws are suitable for cutting different types of large granite slabs with excellent efficiency.

Packaging and Shipping for Diamond Wire Saw Rope

Inner packing: covered by plastic, then packed in a carton; outside packaging is according to the transport way, if by air, we recommend carton package which will reduce the weight; if by sea, we recommend crate which is seaworthy. Other packaging is also available upon your request.
Urgent order with less weight or samples, courier service is recommended;
Normal (regular) order which weight over 45kgs, delivering by air is recommended;
Big diameter saw blades or heavy weight products, shipping by sea is recommended.
Edgestone will offer advices according to the actual order requirements.

Our Services

1. Fine raw materials are used for processing, high grade raw materials, imported cobalt powder and high-quality diamond single crystals, to ensure the best performance of our products.
2. Customized designs are available. We can also help customers design and develop new products, and adjust cutting efficiency and lifespan upon your request.
3. Knowledgeable sales representatives are available to reply all inquiries and e-mails within 24 hours.
4. Every details will be confirmed with you before production.
5. Each processing would be completed by our skillful worker.
6. Strict quality management system. During the whole production process, from raw material choosing, processing to packing, our quality assurance people will strictly control each single and every process to guarantee quality standards and punctual delivery.
7. Detailed and clear pictures will be sent before packing and loading for you.
8. We will keep you update of the order and shipping status till you get the products smoothly.

If you're interested in Diamond Abrasive Cutting Wire Saw, just feel free to contact us, we will keep providing excellent service and good quality products for you.

Contact Info.

Sales Manager: Adam Li
Phone/WhatsApp: 0086-15805032000
Skype: adam-li@outlook.com

Vacuum impregnation also has some obvious disadvantages: impregnated alloys limit the application of some high vapor pressure elements such as refraction, to low temperature dipping    Difficult to test the stained alloy: the equipment is more complex, long dipping time. 2) Carcass material. The carcass consists of a refractory, hard framework component and a more easily meltable component of the church. In order to ensure the normal operation of the drill bit, the drill bit is required to have sufficient wear resistance, toughness, strength and thermal conductivity, and suitable hardness. The commissioned gold has a low melting point and has no mutual solubility or very low solubility with the framework components.  It can not generate high-melting compounds, so it has good wettability to framework components, diamond and steel materials, so that the framework components, diamond can be sintered into a dense high-strength and a certain impact toughness of the whole, at the same time with the steel body Solid quarrel. 3) Cu-Mn-Ni alloys. The data show that in this alloy system, the mechanical properties to be obtained should be such that their composition leaves the range of brittleness and hardness in the binary phase diagram. The brittle range is due to the formation of brittle compounds MnNi and MnNi3. The hard range is the phase decomposition of δ → δ + α Mn, ie precipitation α Mn  As a result, the tough compounds are still produced near the brittle region. In the Cu-Mn binary alloy, the Mn content is in the range of 20o/o. The single-phase solid solution of Mn in copper is δ. In this range, there is a two-phase structure δ +α phase, and the second phase gradually increases with the increase of Mn content. When the Mn content is 36.5% and the temperature is 871°C,  The boundaries are at a minimum. Mn content greater than or less than 36.5%, the crystallizing interval should be widened, which is unfavorable for reducing temperature and sintering. The room temperature solid solubility of Mn in copper is not yet very clear, and is about 24.5% at 400°C. Through the test found: 1 In the range of Mn content less than 25%, with the increase of Mn, the strength of the impregnated specimen gradually increased, and then it increased. 2 In the tested range, the hardness of the specimen increases linearly with the increase of Mn content. 3 In this alloy system, although the increase of Ni content can increase the strength, the performance is subject to the aforementioned conditions. 4 The strength of the test piece is not linear with the press density, and the optimum value of the strength appears at a density of 8.58 g/cm3. Diamond Abrasive Cutting Wire Saw. The choice of the alloy is to make its composition as far as possible structurally single-phase in order to ensure high mechanical properties, but also to consider Possible low temperature. The alloys of No. 1 and No. 4 in Table 7-22 were selected based on this test. Appropriately increasing the Mn content is one of the effective ways to reduce the temperature. 4) Cu-Sn-Ni alloy. In binary Cu-Sn alloys, α-solid solutions based on Cu lattices exist only when the tin content is less than 14%. Above this level, there will be some complex reactions related to the cooling rate. The addition of Ni has an effect on the organization of the system. Although it is not entirely clear, there are data indicating that  The α phase does not undergo grain changes, but the range narrows. In the ternary phase diagram of this alloy system, the saturation limit of the α solid solution is relatively narrow at room temperature. In addition, Cu and Ni are insoluble in Sn, the solubility of Sn in Ni is 15% at 1 135°C, and the maximum solubility of Sn in Cu is 9. 26%.  . In combination with the influence of Sn on the mechanical properties (tensile strength, elongation, impact resistance, etc.) of tin bronze, to obtain better performance, tests have shown that the Sn content cannot exceed 10%. Based on the following considerations, Alloy No. 2 in Table 7-22 has good impregnation effect.