Diamond Wire Saw For Metal Cutting

1. High efficiency and long lifespan
2. Competitive price and stable quality
3. Production capacity: 60,000 meters/month
4. Various wire saw types and sizes available
5. Good cutting result: smooth cutting, flat surface and even size
Description

Diamond Wire Saw For Metal Cutting


Experienced manufacturer of Diamond Wire Saw For Metal Cutting, we supply diamond segments, diamond saw blades, diamond wire saw and diamond grinding tools for stone factories, quarries and wholesalers all over the world.

Application

1. Diamond Wire Saw For Quarry:
Rubber wire is recommended, it can protect the wire saw rope very well and increase the wire’s strength. Rubber possesses excellent characteristic of temperature resistance, and it can be used under situation of water deficient. Strong flexibility can also reduce the cut-in-one-side problem.
2. Diamond Wire Saw For Block Trimming:
Plastic wire is recommended, it can be used to trim marble, granite and other stones. It could cut the blocks accurately with small inter-space.
3. Diamond Wire Saw For Profiling :
Plastic wire is recommended for shaping operations, it could provides a huge range of possibilities. It makes smooth surface and accurate sizes with small inter-space. Stone columns and special shape stone material for building industry can be processed in a much more economic way.
4. Diamond Wire Saw For Reinforce Concrete Cutting:
Diameter 10.5/11.5mm Rubber and Spring wire is recommended. The wires are widely used in the reinforced concrete with more than 5% steel inside. It is used in the building constructions, cutting for houses, bridges, cement pipes and under water buildings.
5. Diamond Multi-Wire Saw For Slab Cutting:
Diamond multi-cutting wire saws are suitable for cutting different types of large granite slabs with excellent efficiency.

Packaging and Shipping for Diamond Wire Saw Rope

Inner packing: covered by plastic, then packed in a carton; outside packaging is according to the transport way, if by air, we recommend carton package which will reduce the weight; if by sea, we recommend crate which is seaworthy. Other packaging is also available upon your request.
Urgent order with less weight or samples, courier service is recommended;
Normal (regular) order which weight over 45kgs, delivering by air is recommended;
Big diameter saw blades or heavy weight products, shipping by sea is recommended.
Edgestone will offer advices according to the actual order requirements.

Our Services

1. Fine raw materials are used for processing, high grade raw materials, imported cobalt powder and high-quality diamond single crystals, to ensure the best performance of our products.
2. Customized designs are available. We can also help customers design and develop new products, and adjust cutting efficiency and lifespan upon your request.
3. Knowledgeable sales representatives are available to reply all inquiries and e-mails within 24 hours.
4. Every details will be confirmed with you before production.
5. Each processing would be completed by our skillful worker.
6. Strict quality management system. During the whole production process, from raw material choosing, processing to packing, our quality assurance people will strictly control each single and every process to guarantee quality standards and punctual delivery.
7. Detailed and clear pictures will be sent before packing and loading for you.
8. We will keep you update of the order and shipping status till you get the products smoothly.

If you're interested in Diamond Wire Saw For Metal Cutting, just feel free to contact us, we will keep providing excellent service and good quality products for you.



Contact Info.

Sales Manager: Adam Li
Email:
info@buydiamondtool.com
Phone/WhatsApp: 0086-15805032000
Skype: adam-li@outlook.com

5 Combining quality of cutter head and metal matrix: 6 Structure and tension state of metal matrix; 7 Machining. Technology and operator's skill level. During the cutting process, the circular saw always rotates in a direction at a constant horizontal speed of 25 65rνs, so that a single diamond rearwardly forms a matrix tail support. Another important parameter is the cumulative depth of cut H, which is the total momentary cutting thickness accumulated at a certain position between the edge of the cutting tool and the workpiece. The depth of cut, H, depends on the cutting direction, the knife angular spacing, and the cutting edge position. If the coolant flows in the same direction along with the saw blade along the same direction as the saw blade, the cumulative chip thickness distribution across the cutting zone is different for up or down cutting conditions, as shown in Figure 4-5. As shown. During down-cutting, a large amount of chips are generated in the diamond into the cutting zone, which leads to a rapid thickening of the mortar, which causes a relatively harsh wear environment for the substrate. The thickening of the mortar during the upward cutting process is slower because the maximum material removal is achieved when the diamond leaves the cutting zone. More importantly, for a continuous copper saw blade, the average thickness of accumulated chips at the exit of the cutting zone does not depend on the cutting method. It can be derived from the following formula: One Z HI‘- Where :heq is related to the chip thickness of the equation. When the block saw blade cuts the workpiece, the situation changes greatly. All cutting edges produce chips at the same time as the track of the section, and then they are discharged into the subsequent nozzle. In this case, because the saw blade design sinks into the water, the average thickness of accumulated chips depends on the length of the gang locus, and Equation (4-2) will no longer hold. In the event of excessive matrix wear, shorter nodes will be more advantageous at the same wheel clearance (LL IL2 ). It must be emphasized that the nozzle on the copper wheel of the saw blade will prevent excessive chips from accumulating in the cutting zone. However, in this special situation Under the circumstances, the accuracy of the quantitative estimation of H is affected by the inability to determine the amount of chips that will be drawn into the cutting zone of the next rock mass as the water is ingested. Diamond Wire Saw For Metal Cutting  Section II Theoretical Model of Frame Saw Cutting  Frame saws have long been used in stone sawing applications. These saw blades are subjected to periodic cutting action. At a relatively low speed with a sinusoidal change, the maximum speed is 2 m/s. Periodic movement of the saw blade reduces the stone chip removal speed from the cut. For the substrate, this constitutes a harsh wear environment, which can easily lead to abnormal diamond pullout. This is mainly caused by    The matrix did not form tail support for the diamond and the forces acting on the diamond particles changed.    Figure 4-6 Schematic diagram of the principle features of the cutting area of ​​the frame saw  Similar to the circular saw, in the frame saw model, it is assumed that the stone is cut by a thin linear saw blade. The linear saw blade consists of a series of single, equally spaced blades with the same width as the saw blade and fixed to the saw blade. From Fig. 4-7 it is obvious that the instantaneous horizontal speed of the saw blade depends on the position of the flywheel. Under this condition, changing the moving direction will obtain the maximum chip thickness, which can be estimated by the formula (4 leads): V, 1 l - 2L \ h = iarccosI 2-1 1 (4 -3) n I l I Where: where one flywheel speed, turn / minute (r / n1in); l One stroke length, m; L3 knife spacing, m.       Figure 4-7 Frame saw sawing motion  Compared to circular saws, since the frame saw cuts at a lower horizontal speed, it has less influence on the diamond blade. Therefore, considering the strength of diamond, more consideration should be given to the wear resistance of the matrix.

Review